#!/bin/sh
#
# This file was produced by running the Policy_sh.SH script, which
# gets its values from config.sh, which is generally produced by
# running Configure.
#
# The idea here is to distill in one place the common site-wide
# "policy" answers (such as installation directories) that are
# to be "sticky". If you keep the file Policy.sh around in
# the same directory as you are building Perl, then Configure will
# (by default) load up the Policy.sh file just before the
# platform-specific hints file and rewrite it at the end.
#
# The sequence of events is as follows:
# A: If you are NOT re-using an old config.sh:
# 1. At start-up, Configure loads up the defaults from the
# os-specific hints/osname_osvers.sh file and any previous
# Policy.sh file.
# 2. At the end, Configure runs Policy_sh.SH, which creates
# Policy.sh, overwriting a previous Policy.sh if necessary.
#
# B: If you are re-using an old config.sh:
# 1. At start-up, Configure loads up the defaults from config.sh,
# ignoring any previous Policy.sh file.
# 2. At the end, Configure runs Policy_sh.SH, which creates
# Policy.sh, overwriting a previous Policy.sh if necessary.
#
# Thus the Policy.sh file gets overwritten each time
# Configure is run. Any variables you add to Policy.sh will be lost
# unless you copy Policy.sh somewhere else before running Configure.
#
# Allow Configure command-line overrides; usually these won't be
# needed, but something like -Dprefix=/test/location can be quite
# useful for testing out new versions.
#Site-specific values:
case "$perladmin" in
'') perladmin='none' ;;
esac
# Installation prefixes. Allow a Configure -D override. You
# may wish to reinstall perl under a different prefix, perhaps
# in order to test a different configuration.
# For an explanation of the installation directories, see the
# INSTALL file section on "Installation Directories".
case "$prefix" in
'') prefix='USEPERLDIR/perl' ;;
esac
# By default, the next three are the same as $prefix.
# If the user changes $prefix, and previously $siteprefix was the
# same as $prefix, then change $siteprefix as well.
# Use similar logic for $vendorprefix and $installprefix.
case "$siteprefix" in
'') if test "USEPERLDIR/perl-addons" = "USEPERLDIR/perl"; then
siteprefix="$prefix"
else
siteprefix='USEPERLDIR/perl-addons'
fi
;;
esac
case "$vendorprefix" in
'') if test "" = "USEPERLDIR/perl"; then
vendorprefix="$prefix"
else
vendorprefix=''
fi
;;
esac
# Where installperl puts things.
case "$installprefix" in
'') if test "USEPERLDIR/perl" = "USEPERLDIR/perl"; then
installprefix="$prefix"
else
installprefix='USEPERLDIR/perl'
fi
;;
esac
# Installation directives. Note that each one comes in three flavors.
# For example, we have privlib, privlibexp, and installprivlib.
# privlib is for private (to perl) library files.
# privlibexp is the same, except any 'USEPERLDIR' the user gave to Configure
# is expanded to the user's home directory. This is figured
# out automatically by Configure, so you don't have to include it here.
# installprivlib is for systems (such as those running AFS) that
# need to distinguish between the place where things
# get installed and where they finally will reside. As of 5.005_6x,
# this too is handled automatically by Configure based on
# USEPERLDIR/perl, so it isn't included here either.
#
# Note also that there are three broad hierarchies of installation
# directories, as discussed in the INSTALL file under
# "Installation Directories":
#
# =item Directories for the perl distribution
#
# =item Directories for site-specific add-on files
#
# =item Directories for vendor-supplied add-on files
#
# See Porting/Glossary for the definitions of these names, and see the
# INSTALL file for further explanation and some examples.
#
# In each case, if your previous value was the default, leave it commented
# out. That way, if you override prefix, all of these will be
# automatically adjusted.
#
# WARNING: Be especially careful about architecture-dependent and
# version-dependent names, particularly if you reuse this file for
# different versions of perl.
# bin='USEPERLDIR/perl/bin'
# scriptdir='USEPERLDIR/perl/bin'
# privlib='USEPERLDIR/perl/lib/5.8.4'
# archlib='USEPERLDIR/perl/lib/5.8.4/i686-linux-ld'
# man1dir='USEPERLDIR/perl/man/man1'
# man3dir='USEPERLDIR/perl/man/man3'
# Preserving custom html1dir
html1dir='USEPERLDIR/perl/html'
# Preserving custom html3dir
html3dir='USEPERLDIR/perl/html'
# sitebin='USEPERLDIR/perl-addons/bin'
# sitescript='USEPERLDIR/perl-addons/bin'
# Preserving custom sitelib
sitelib='USEPERLDIR/perl-addons/lib/site_perl/5.8.4'
# sitearch='USEPERLDIR/perl-addons/lib/site_perl/5.8.4/i686-linux-ld'
# Preserving custom siteman1dir
siteman1dir='USEPERLDIR/perl-addons/man/man1'
# Preserving custom siteman3dir
siteman3dir='USEPERLDIR/perl-addons/man/man3'
# Preserving custom sitehtml1dir
sitehtml1dir='USEPERLDIR/perl-addons/html'
# Preserving custom sitehtml3dir
sitehtml3dir='USEPERLDIR/perl-addons/html'
# vendorbin=''
# vendorscript=''
# vendorlib=''
# vendorarch=''
# Preserving custom vendorman1dir
vendorman1dir=' '
# Preserving custom vendorman3dir
vendorman3dir=' '
# Preserving custom vendorhtml1dir
vendorhtml1dir=' '
# Preserving custom vendorhtml3dir
vendorhtml3dir=' '
# Lastly, you may add additional items here. For example, to set the
# pager to your local favorite value, uncomment the following line in
# the original Policy_sh.SH file and re-run sh Policy_sh.SH.
#
# pager='/usr/bin/less'
#
# A full Glossary of all the config.sh variables is in the file
# Porting/Glossary.